The Light Source 2′ x 2′ Drop-In Fixture

Electrical

• The Light Source, Inc. RL Series fixture’s LED driver has a universal input range of 100VAC to 277VAC 50/60HZ with no adjustments required, and a mean time between failures of 330,000 hours. The 150 Watt LED driver may be factory preset to 80, 100, 120, or 150 Watts output.
• RGBW LED drivers are set to 120 Watts. The Light Source, Inc. RL Series fixture’s all include the UL required thermal protector that is specific to the supply voltage.
• The LED driver has active power factor correction with 99% PF at 120VAC, ATHD of 7%, and draws only .84 Amps at 100 Watts. Inrush current is limited, allowing up to 12 of the 100 Watt LED fixtures to run on a single pole 20 Amp 120VAC circuit breaker.
• The LED fixture responds quickly, producing full light output in 2-3 seconds after power is applied. Relays are not required to turn The Light Source, Inc. RL series fixtures off between uses. The fixtures are fully rated for 24/7/365 operation. This enables the fixtures to instantly respond to DMX control signals without waiting for relays to sequence and fixture boot time. Standby wattage is less than 1 Watt with power on and DMX at level zero. The annual quiescent power draw is less than 9 KWH.

Connections

• Power connections may be hardwired internally with a ½” or ¾” conduit connections and the provided flip lever Wago connectors, or connected to an optional external flush Neutrik PowerCon connector.
• DMX data connections may be hardwired with the provided IDC or screw terminal plugin connectors; or the optional external flush mounted Neutrik 5 pin XLR, 3 pin XLR, or RJ-45 Ethercon connectors. Optional LumenRadio wireless DMX is also available to provide control data to the fixture.

Control

• The Light Source, Inc. RL Series fixtures are fully DMX dimmable to zero with extremely smooth 24 bit dimming utilizing only single channel DMX dimming control. The dimmer microprocessor is able to use over 16 million steps from full intensity to off for incredibly smooth dimming.
• The RGBW DMX control outputs 16 bit analog on four or five channels of DMX. There is no flicker on video with either line scan or global camera shutters interacting with the 30khz output frequency.
• The DMX line is fully isolated to 2,500 Volts per microsecond. The Light Source proprietary Thermal Mass Equivalence may be enabled during installation by turning dip switch 1 to off. This setting allows the DMX control channel 512 to change the dimming performance to emulate a large or small incandescent lamp, or to change the dimming performance to an instant response. The fixture is also available in a non-dimming version.

Standard White Light LED Module

• Based on Cree’s product testing, The Light Source, Inc.’s RL Series fixture’s standard LED module offers over 100,000 hours of life operating from 80 to 150 input Watts.
• Individual LEDs operate close to half of their maximum drive current even when the RL series fixture is driven at 150 Watts. The low drive current increases the LED brightness and life. Cree LEDs have a pleasing full spectrum light with all the visible colors represented in the fixture’s spectral output.
• 60 individual LEDs are carefully factory selected to maintain minimal color variance between LED modules. The white LEDs are available in color temperatures of: 2700K, 3000K, 3500K, 4000K, and 5000K. The standard LED module has a typical CRI of 82.

RGBW LED Module

Optical

• Optical systems are available in 78, 65, 52, 44, 36, 30, 25, and 20 degree beam angles. Sixty tightly clustered Cree LEDs and a 6” tempered borosilicate Fresnel lens combine to provide a single source look that completely emulates an incandescent source.
• Efficient use of the lumens generated by the LED cluster is accomplished by directing the LED output to the task area. An additional condenser lens is utilized to maximize the lumen output on the 52 degree and tighter beam spreads.
• RGBW fixtures are available in beam angles of 80 degrees, 65 degrees and 52 degrees.

Thermal

Mounting

Finish